{pboot:if('

Performance advantages:
 1. Made of environmentally friendly solvents and a variety of special anti-rust additives, after being applied to the metal surface, the solvent evaporates and leaves a uniform anti-rust film. Widely used for long-term anti-rust protection of steel parts.
 2. The product has good human sweat and water displacement performance, has excellent anti-corrosion performance for ferrous and non-ferrous metals, and has the characteristics of thin coating, easy to use, and easy to remove. The anti-rust cycle is as long as 9-12 months
 Product advantages:
 1. Water displacement type: can quickly remove the water film on the surface of metal parts and attach a layer of anti-rust film on it to protect the metal from corrosion.
 2. Low viscosity: has extremely strong permeability and rust resistance, and can be used for small hardware parts.          
 3. Low cost: low cost per unit area.
 4. Easy to clean: a transparent oily film is formed on the metal surface, which can be easily washed off with petroleum solvent or kerosene.
 Scope of application:
 1. Mainly used for removing water film and rust prevention on the metal surface between processes, and is more ideal for the subsequent processing of steel products processed with water-soluble cutting fluids.
 2. Widely used for long-term rust protection of steel parts.
 Product parameters:

< /tr>

40°C viscosity mm2/s	3.5-4.5
Main ingredients	Mineral oil, solvent, water
Appearance and properties:	Yellow transparent liquid
Process requirements	Anti-emulsification type
Anti-rust cycle (month)	12
Melting point (℃)	<-20
Boiling point (℃)	190-240
Relative density (water, g/ml3)	0.8514±0.02
Flash point (℃)	70
Autoignition point (℃)	>300
Oil film requirements	Water displacement type
Artifact type	Precision parts
Copper corrosion 100°C	≤1
Salt spray test 45# steel, hours	18
Wet heat test 45# steel, day	≥10

Notes:
 1. This series includes P3 and P3A, of which P3 is not suitable for copper materials and hot and humid environments, and P3A is not suitable for salt spray environments. < br/>  2. Immerse the metal parts with water directly into the dehydrating oil for about 1-3 minutes, and vibrate the parts continuously. For parts with pores, blind holes, and inner cavities, shake them more to thoroughly remove the water. Dehydration.
 3. The bottom of the oil tank should be designed to be conical, and a valve should be installed at the bottom to drain the accumulated water at any time. At the same time, a movable metal net should be installed 10cm from the bottom of the oil tank to prevent metal parts from touching the accumulated water, ensuring dehydration and Anti-rust effect.
 4. If you spin off the water droplets first and then dehydrate them, the effect will be better.

'!='')}

Dehydration replacement rust inhibitor P3 series

{/pboot:if} {pboot:if('

Performance advantages:
 1. Made of environmentally friendly solvents and a variety of special anti-rust additives, after being applied to the metal surface, the solvent evaporates and leaves a uniform anti-rust film. Widely used for long-term anti-rust protection of steel parts.
 2. The product has good human sweat and water displacement performance, has excellent anti-corrosion performance for ferrous and non-ferrous metals, and has the characteristics of thin coating, easy to use, and easy to remove. The anti-rust cycle is as long as 9-12 months
 Product advantages:
 1. Water displacement type: can quickly remove the water film on the surface of metal parts and attach a layer of anti-rust film on it to protect the metal from corrosion.
 2. Low viscosity: has extremely strong permeability and rust resistance, and can be used for small hardware parts.          
 3. Low cost: low cost per unit area.
 4. Easy to clean: a transparent oily film is formed on the metal surface, which can be easily washed off with petroleum solvent or kerosene.
 Scope of application:
 1. Mainly used for removing water film and rust prevention on the metal surface between processes, and is more ideal for the subsequent processing of steel products processed with water-soluble cutting fluids.
 2. Widely used for long-term rust protection of steel parts.
 Product parameters:

< /tr>

40°C viscosity mm2/s	3.5-4.5
Main ingredients	Mineral oil, solvent, water
Appearance and properties:	Yellow transparent liquid
Process requirements	Anti-emulsification type
Anti-rust cycle (month)	12
Melting point (℃)	<-20
Boiling point (℃)	190-240
Relative density (water, g/ml3)	0.8514±0.02
Flash point (℃)	70
Autoignition point (℃)	>300
Oil film requirements	Water displacement type
Artifact type	Precision parts
Copper corrosion 100°C	≤1
Salt spray test 45# steel, hours	18
Wet heat test 45# steel, day	≥10

Notes:
 1. This series includes P3 and P3A, of which P3 is not suitable for copper materials and hot and humid environments, and P3A is not suitable for salt spray environments. < br/>  2. Immerse the metal parts with water directly into the dehydrating oil for about 1-3 minutes, and vibrate the parts continuously. For parts with pores, blind holes, and inner cavities, shake them more to thoroughly remove the water. Dehydration.
 3. The bottom of the oil tank should be designed to be conical, and a valve should be installed at the bottom to drain the accumulated water at any time. At the same time, a movable metal net should be installed 10cm from the bottom of the oil tank to prevent metal parts from touching the accumulated water, ensuring dehydration and Anti-rust effect.
 4. If you spin off the water droplets first and then dehydrate them, the effect will be better.

'!='')}

{/pboot:if}

Performance advantages:
 1. Made of environmentally friendly solvents and a variety of special anti-rust additives, after being applied to the metal surface, the solvent evaporates and leaves a uniform anti-rust film. Widely used for long-term anti-rust protection of steel parts.
 2. The product has good human sweat and water displacement performance, has excellent anti-corrosion performance for ferrous and non-ferrous metals, and has the characteristics of thin coating, easy to use, and easy to remove. The anti-rust cycle is as long as 9-12 months
 Product advantages:
 1. Water displacement type: can quickly remove the water film on the surface of metal parts and attach a layer of anti-rust film on it to protect the metal from corrosion.
 2. Low viscosity: has extremely strong permeability and rust resistance, and can be used for small hardware parts.          
 3. Low cost: low cost per unit area.
 4. Easy to clean: a transparent oily film is formed on the metal surface, which can be easily washed off with petroleum solvent or kerosene.
 Scope of application:
 1. Mainly used for removing water film and rust prevention on the metal surface between processes, and is more ideal for the subsequent processing of steel products processed with water-soluble cutting fluids.
 2. Widely used for long-term rust protection of steel parts.
 Product parameters:

< /tr>

40°C viscosity mm2/s	3.5-4.5
Main ingredients	Mineral oil, solvent, water
Appearance and properties:	Yellow transparent liquid
Process requirements	Anti-emulsification type
Anti-rust cycle (month)	12
Melting point (℃)	<-20
Boiling point (℃)	190-240
Relative density (water, g/ml3)	0.8514±0.02
Flash point (℃)	70
Autoignition point (℃)	>300
Oil film requirements	Water displacement type
Artifact type	Precision parts
Copper corrosion 100°C	≤1
Salt spray test 45# steel, hours	18
Wet heat test 45# steel, day	≥10

Notes:
 1. This series includes P3 and P3A, of which P3 is not suitable for copper materials and hot and humid environments, and P3A is not suitable for salt spray environments. < br/>  2. Immerse the metal parts with water directly into the dehydrating oil for about 1-3 minutes, and vibrate the parts continuously. For parts with pores, blind holes, and inner cavities, shake them more to thoroughly remove the water. Dehydration.
 3. The bottom of the oil tank should be designed to be conical, and a valve should be installed at the bottom to drain the accumulated water at any time. At the same time, a movable metal net should be installed 10cm from the bottom of the oil tank to prevent metal parts from touching the accumulated water, ensuring dehydration and Anti-rust effect.
 4. If you spin off the water droplets first and then dehydrate them, the effect will be better.